How to remove crankshaft pulley

Normally the pulley is not that hard to remove but some get stuck. You may have to use a harmonic balancer removal tool, available for loan at Auto Zone. Once it loosens it should slide right off. Note that you have to put the bolt back.

Then, reinstall the center bolt minus the large washer, into the. You need to pull your motor. You my friend have an Interference engine.

This means if you let your belt break the valve will hit your pistons and you will need to either rebuild the engine or replace it! All you need is a simple pulley removing tool. DIY car repair with Scotty Kilmer, an auto. Crankshaft pulley removal.

Position the puller in front of the pulley. How to use crankshaft pulley tool. Hold the point of the central threaded puller bolt in the detent on the end of the crankshaft and rotate the puller until at least two of the slots in the puller align with the threaded holes in the pulley.

A crankshaft pulley powers components on the crankshaft. Remove stuck crankshaft bolt on. Then, using the bolts that came with the tool, begin tightening the tool. Continue tightening until the pulley is released from the crankshaft.

Step 4: Connect your crankshaft pulley remover tool to your power drill and tighten it securely into place. With your power drill set in. To remove the pulley , reverse the power drill when you pull the trigger.

Undo the bolt of the pulley and remove the defective pulley from the engine. Take the new crankshaft pulley and place it on the engine. Step 5: Installing The New Pulley.

Screw the bolt at the center of the new pulley. Install the bolt for the crankshaft pulley just a couple of threads into the crankshaft and then install the puller into the threaded holes and push off the crankshaft bolt. A woodruff key is installed in the hub of a pulley or gear so that the pulley or gear does not slip off the shaft it is attached to or spin freely. Precleaning is not necessary.

The experts at Honda Tuning Magazine give you a little tip on how to easily removal your Honda engine crank pulley. Easily remove crank pulley bolts on Honda and Acura engines with this tool. Need to remove the crankshaft timing pulley to get the oil pump off. Can someone tell me how to hold the pulley tight while trying to unscrew the pulley bolt? Jump to: navigation, search.

Torque the pulley and crankshaft bolts to spec. Find great deals on eBay for crankshaft pulley removal tool. The crankshaft pulley (harmonic balancer) is mounted on the end of the crankshaft.

In order to remove Mercedes-Benz harmonic balancer, you will need Mercedes crankshaft pulley tool to hold the crankshaft in place and stop it from rotating. Next, remove the radiator and crankcase pulley , followed by the timing chain to free up the heads, then the camshaft and finally the head itself. Anyway, this is just about removing the crankshaft pulley as I have heard of nightmares doing it. If you mean you’re not able to remove the crankshaft bolt, it requires a very good impact gun or a special tool that prevents the crank from rotating when attempting to remove the crankshaft bolt. This is not for the faint of heart, not for the clumsy, and is quite dangerous if you have no prior experience with tools or working on cars.

I used a 3-jaw gear puller to remove the.

The bolt should turn the opposite direction. I have looked for a flywheel inspection cover, so I can use a bar to hold crankshaft to remove retaining bolt, I cannot see such a cover. The large bolt in the center does NOT hold the harmonic dampener ( crankshaft pulley ). It holds the crankshaft sprocket to the actual crankshaft.

As far as I know you have to remove. Location of the crankshaft pulley bolte (1) and the hub bolt (2) Fig. Unfasten all the pulley and hub bolts, remove the pulley and install a suitable puller on the crankshaft hub Fig. Unfortunately, they also need to come off in order to remove the crankshaft pulley and the crankshaft seal behind it.

Typically this is done in order to change the timing belt, but the crankshaft pulley itself will fail on its own as well. This is because the pulley is attached to various components through belts. Place a screwdriver across the teeth of the flywheel. But that is probably the hardest one to remove. This happens because this bolt is very well tighten and when you’ll.

Unscrew and remove the push lawnmower blade retaining bolt, lawnmower blade and washer from the crankshaft. When working with a riding lawnmower, you must remove the pulley retaining bolt and. Just changing the cambelt as its long overdue. So long infact that Ive forgotten how I got the crank pulley off last time to get the belt off.

Just tried putting it in 1st gear with handbrake on but the engine still seems to turn. Some Honda models have CW rotating engines others CCW. Use a strap wrench around the crankshaft pulley.

The center crankshaft bolt is a single use part. If you tried to remove it, you need to replace it, because it needs to be torqued with a torque wench.