Hood release cable

Your order may be eligible for Ship to Home, and shipping is free on all online orders of $35. Check here for special coupons and promotions. This hood release cable has the following specifications with Handle. In order to keep our prices low, we have the following purchasing poli. We know our parts and products.

Restore and maintain the opening of your hood with our Hood Release Cable. Made of quality stainless steel, it naturally resists corrosion. Easy to use parts catalog. I used a large flat head screwdriver to break into my engine compartment.

Constructed of high-quality stainless steel, it naturally resists corrosion. Plus, it’s engineered to counteract the wear and tear that can lead to snapping and sticking. In our first Back to Basics video Ed and I look at replacing the hood release cable - in this case on a Jeep Grand Cherokee.

A damaged hood release cable is a snap to replace and is relatively inexpensive. How does the Hood Release Cable work? The hood release cable is attached at one end to the the hood release latch, as discussed. Also as discusse it is attached on the other end to the hood latch, which is the same part at the front of the hood that is seemingly impossible to find once the hood release has been pulled. It is just what you need to replace broken or defective cable and bring back the safety and integrity of a safely latched hood.

Parts are just part of what we do. Get yours online today and pick up in store. Hood release cables are designed to facilitate the opening of your hood. As with the rest components, time can bring wear and tear to these cables.

Grab the round ball on the end of the cable in the latch, and lift it up and out of the retainer spring. A hood latch release cable can break at any point along its length, though it will do so most often at the ends. Remove the screw holding the cable to the latch. If the attachment point on the release breaks, you’ll need to replace the release , but likely not the cable. If the hood latch release cable breaks, you may be unable to open the hood.

The other cables (serviced as one part) run to each hood latch. One cable runs from the hood release handle to the cable junction under the hood. The cables that run to the hood latches tend to crack, allowing moisture to enter the cable. I cannot release the hood , pulled feet cable out from under the dash.

Find Dorman Hood Release Cables and get Free Shipping on Orders Over $at Summit Racing! Do you have a broken or rusted-out hood release cable ? Whether you’re maintaining your Shark Corvette or completing a full restoration, our selection of CCorvette Body and Fiberglass parts is unsurpassed. A hood release cable runs from this mechanism to the hood release lever inside the vehicle. On the left is the old hood release cable , on the right is the new one from 1A Auto. You can see they are identical and will fit exactly the same.

Tie the wire onto your new hood release cable. Had to use vise grip to pull open the latch. Trunk Latch Release Cable Replacement Service What is the Trunk Latch Release Cable all about? Corvette hood release cables can make the difference between easy engine compartment access and a stuck hood.

Don’t get caught with your Corvette hood stuck because of a bad hood release cable. The factory cable finally snapped making it difficult to open the hood. Purchased this cable as a replacement at half the cost of the factory cable. The hardest part of the install is routing the new cable through the firewall but can be accomplished with a little patience.

Peruse our tech articles for information on any problems you may be having. This cable spans the distance from the release handle or push button, securely fastened under your dash boar directly to the hood latch.

Without your Ford Windstar hood release cable , looking under the hood will be a difficult task to say the least. Corvette Engine And Relate Corvette Hood And Corvette Hood Latch. The locking hood release cable is the cable that allows you to unlock your hood by pulling a lever inside your truck. It is a simple mechanism that uses no electronics. The handle you pull is connected to a metal cable that is in turn connected to the latch that holds the hood closed.

Today were going to discuss the advantages of a made to. Open the hood , and on each side of the opening near the fenders you’ll see rubber stops for the hood. You turn those rubber stops to raise them so when the hood latch is pulled those stops pop the hood open. Also, the cable may be unsupported somewhere.

Look for a broken tie down. If the cable broke by the hood release under the dash, you may be able to use a set of pliers to pull on the cable. NOTE: COMBINATION HOOD AND TRUNK RELEASE CABLE KITS: This Kit has a release handle assembly with both an inside arm and an outside arm.

The two cables are separated by a spacer block. The installation procedure will be the same as above. The outside arm is intended to be for the hood release , and the inside arm is intended to be for the trunk.

This billet hood release handle has a satin finish.

Designed for easy installation and removal. The cable can be unhooked from the handle without affecting adjustments. Find parts and applications on our site. Use our Dealer Locator to find an authorized Crown dealer near you. Overview Dorman Products is a leading supplier of original equipment dealer exclusive automotive and heavy duty replacement parts.

Choose your year below to refine your search. Dorman Products is an unmatched leader in supplying automotive and heavy-duty replacement parts including hardware, brake parts, and fasteners to the automotive and heavy-vehicle aftermarkets.