Coolant drain plug

We know our parts and products. Only left in stock - order soon. How to drain the coolant anitfreeze. I have the radiator drained and rinsed out. Now I want to get the rest of the coolant out.

Is the engine block coolant drain plug , the dark color, hex-hea screw plug located above and to the right of the oil filter cap, and between a bracket and the engine block, in the below picture? Open the petcock and drain the coolant from the radiator and cooling lines of the engine. Follow the same steps you used to drain the old coolant from the radiator to drain the water you added. Drain the water from the radiator.

This water will flush out the remaining old coolant as you drain it, leaving your coolant system ready for you to fill it with a new coolant mixture. Im about to drain the coolant on my 03. Anybody know exactly where it is? The radiator plug is obvious on the bottom of the radiator. Look at the coolant in the drain bucket.

If it appears cloudy or muddy you should replace it with fresh coolant. Tighten the radiator rug plug with the ratchet after you drain the coolant. Open the radiator cap at the top of the radiator and pour the recommended amount of fresh coolant for your car.

Find Engine Coolant Plug Fasteners and get Free Shipping on Orders Over $at Summit Racing! Dremmel as much as I can of the plug out, and then try and collapse it. Drill out the old plug and retap the hole and fit with a larger plug. The coolant drain plug seal allows you to easily drain the coolant of a radiator when it is time to replace the coolant. Damage or wear to the drain plug could make your radiator leak, which could empty it and lead to overheating.

I found a coolant drain plug on the back of my engine block. Align the coolant drain pan beneath the radiator in the location of the drain plug.

It is located on the bottom of the radiator closest to the passenger side (near the lower radiator hose). Turn the drain plug counterclockwise all the way until it stops. When you pull the radiator plug on the 2. After draining both you will still have some coolant in the system, which you can do a few cycles of distilled water to flush it out if you choose.

Read the tech article on Block Plug Basics, brought to you by the experts at Chevy High Performance Magazine. Draining cooling systeRemove the radiator drain plug and drain the coolant (green arrow). You can use a flat or Phillips head screwdriver. Allow the coolant to drain into the bucket. However, this drain valve can begin to have leaking problems over the life of your car.

Fixing a leaking radiator drain petcock is a simple process that requires some basic tools and.

Locate the drain valve on the bottom of the radiator, open it up, and drain the system in a drain pan. Step - Refill with distilled water. Once the coolant is drained and you have closed the valve, refill the coolant system with distilled water. But now, the only way to remove the coolant from your Silverado is to disconnect the lower radiator hose and allow it to drain into your drain pan.

Normally, a coolant flush is a straightforward process: remove a couple drain plugs to let the old coolant drain out, put the plugs back in, and refill the coolant. In fact, that is the case on pre-vehicles. You should have the same 4. L with 34k miles, and im trying to drain the coolant. The engine does not have a coolant drain plug.

To drain the block you need to remove the very bottom hose on the motor and let it drain that way, to get all the water out of t … he block start. By continuing to use this site you consent to the use of cookies on your device as described in our cookie policy unless you have disabled them. The front engine block drain is located between the starter and the engine oil filter. The rear engine block drain is located by the engine crank sensor. Unless you have had a leak or work done which requires coolant change, the owners manual has this as a 150k (miles) or 5yr.

Look for your engine block heater. This way I can replace all the coolant if the plug ends up coming out in my hand! I only need to drain enough coolant to do the EGR-cooler service, so could siphon etc, but am supposed to use the special funnel at refill anyway. Coolant left in the bottom of the overflow tank is normal if you do not remove the engine drain plug s well as the radiator drain plug. Did that screw up anything.

Monk Sorry for the blurry. The heat exchanger itself is aluminum, hence the dissimilar metal and potential for corrosion. Leaking coolant is usually a sign that your water pump needs to be replaced. This video shows you how to quickly plug it.

Looking under the engine, I spotted the drain plug for the radiator, but not the engine block drain plug mentioned in the Haynes Manual. Your CCorvette requires that you drain and refill the coolant in the radiator every years or 100miles and every years or 30miles thereafter. In order to do the job, you need three gallons of coolant. No the part circled is NOT the drain plug. But, the good news is, the drain plug IS showing in the picture you provided.

The drain plug is made out of plastic, which makes it fragile so use caution when removing. It has a cross shaped pattern on it, similar to a philips head fastener.