Clear coat for bare metal

Its designed to bond to basecoat. Projects - clear coating bare metal car ? Need advice: best way to paint clear on bare. SprayMax 2K over bare steel.

This will give you a Matte, Satin, Flat type of appearance. Our clear coats are an effective barrier against vapor and moisture, preventing penetration of water and salts to the bare metal surface. I did some research and a paint rep told me clear Imron had etching properties and was super hard.

We ground the metal in grit and sprayed coats of Imron over it.

Curious if anyone is clear coating bare metal and what your using? I found Eastwood sells an aerosol for this purpose. This water clear high gloss clear coat remains permanently flexible and is able to perform in the toughest environments without yellowing, cracking or peeling.

Now that the metal is in place some of the finish is coming off and taking the rust with it (rusted look was the desire) Is there a product that we can put over the lacquer that will stand up to abuse (prefer clear coat ) or do we have to take off the lacquer before we can put anything else on it. This self- leveling formulation, resists chips, cracks, fading and yellowing. If this is your first visit, be sure to check out the FAQ by clicking the link above.

You may have to register before you can post: click the register link above to proceed. Possible to clearcoat bare metal ? Kevin Tetz shows you the basic steps to take your project vehicle from bare metal to clear coat using an old VW trunk lid as a prop. First put your Contour Polyester Bodyfiller, then coat with.

Think of the reflection, blinding both driver and traffic. I think certain parts would be very cool left bare and clear coated. Maybe a bare metal and clear coated wide stripe down the length of the painted car.

BMW frame is clearcoat om bare metal , i ride the shit out of it, and i see no rust anywhere. Laser See more like this SwitchEasy Nude Ultra Slim 0. I clear coated my gas tank when it was bare metal and after about months it started to look like it was flaking, but it was the bottom layers seperating from the metal. Legs are made from new hot rolled steel so they have a layer of oil on them and maybe just one or two surface rust blotches. I would like to clear coat bare metal table legs.

WONT give you any corrosion protection. NEED some sort of an etching primer on you bare metal. UNLESS the product you are using is DTM. It can be used alone as a base coat on bare metal and will fix the rust while preserving the appearance.

I will typically use the ceramic that is heat cured or bake the clear is an air cure product. Brushing clear on is for beginners or pool fence builders. Yes, works well but make sure the bare metal is absolutely clean and free of debris. I wanted to apply a clear coat to protect their work.

It may have changed color a shade. If you fail to clear coat your image it may be damaged. Having done this type of work a LOT in the past I have found that it is best to plastic wear gloves when handling the bare metal. If the paint job wasn’t bad to begin with, just.

Print Email Jason Stahl, Editor,. Once you reclean, you apply one more medium coat of Plas-Stick and allow it to dry. Some bare metal cars do have a clear coat , although that approach lacks a little in the authenticity department, and moisture can sometimes still get beneath the surface, allowing rust to become visible beneath the supposedly impenetrable finish.

Silver is going to look, well, silver. Recommended for use on plastic hubcaps and wheels made of aluminum or steel. So the steel left in a raw state is best not advise and even a clear coat over the steel would be better (will still be able to wear it off, exsposing the bare metal ). I did an FZ7that way, stripped the steel tank down to bare metal , polished the heck out of it. I used a good fast part urethane clear coat , and never had any problems. Painting clear over metal is kind of a niche application.

When you have finished sanding all of the bodywork you are likely to have some bare metal spots from sanding. Now let the vehicle set overnight. But, if the chip is small, and even if it goes through the clear coat and deep into the paint, the best thing may be to try a simple touch-up.

Strip to bare metal - This truly is the most “correct” way to prep a vehicle for a repaint, especially a classic or “older” car. This method will allow you to uncover any potential rust or corrosion that will need to be addressed before you put on any topcoats. When the paint started rusting through I coated it with clear rustoleum and it saved my job! I have used it over wood paint where it needs some extra protection and even bare wood.

For a car, the paint job has many layers. After that, the base coat goes on. There is the bare metal which some primer is sprayed onto. Perhaps moisture got trapped in the clear causing what we call Blushing. Please let me know if you have any other questions.

Clean the metal and apply coats of the clear formulation first. Let it dry and see if you like the finish. If so, add another coat of the clear finish. SPACECRAFT PROVEN PROTECTION. Developed over years ago for the Apollo space program, Nyalic is more than a clear coat surface protectant.

Bare - Metal Foil is the number one model detailing foil. It is a high-performance technology developed to protect metal and painted surfaces from corrosion in the most extreme environments. A clear coat contains no pigments and it is unpigmented finish. It just provides a cover or sheathe to the finish paints applied.

Without the pigmented finish paint as its base, it shall fail. Now if you sand a finish coat or lacquer coat , you shall have partly removed a coat and would not have reached the bare metal. Clear Varnish or Laquer Coat.