Temperature sending unit location

Vehicle is Ford F1with 3motor. My check engine light is on due to this sender not functioning correctly. The ECT gauge sending unit resistance should be 1ohms at a temperature of 133°F (56°C). The job of the temperature sending switch or coolant temperature sender in your vehicle is to let you know, through the temperature gauge on the dashboar when the engine is operating under abnormal temperatures. Always consult a professional repa.

Temperature Sending Units Installation Instructions 1. Find a location where temperature can be measured such as the existing sending unit , temperature switch, or pipe fitting normally located on the front of the intake manifol or on the side of the cylinder head. Use a sending unit with the same thread as the manifold threa or cylinder head. The temperature sending unit , more properly known as a temperature sensor, is one of the most important sensors in your car. It is the sensor that tells the computer when the engine has warmed up sufficiently for the computer to pay attention to the many other sensors on the engine and exhaust.

Problems with the coolant temperature sending unit can cause faulty readings from the temperature gauge or light. You might find that the gauge reads cold even when the engine has been running. There is a simple test you can run to ensure that the problem is with the ECT sensor and not the gauge. A functional coolant temperature sensor not only ensures a safer ride, but it also prevents your vehicle from using more gas than necessary. However, if you want to install both senders.

I have replaced the water pump, clutch fan and thermostat because my temp runs over 210. This brass water temperature sending unit threads into the intake manifold and sends the information to the temperature gauge in the interior of your Mustang. Jeep Wrangler and Toyota Tacoma parts at one trustworthy location. It ended up being a bad temperature sending unit.

It has one wire atached to it. I have tested the temperature sending wire and the gauge and both appear to work fine. I ground the temperature sending wire on the alternator and the gauge will jump up to hot but fairly slowly. Find great deals on eBay for temperature sending unit.

Engines this part is found on include 4. Been all over the goofy thing. Answered by a verified Technician We use cookies to give you the best possible experience on our website. By continuing to use this site you consent to the use of cookies on your device as described in our cookie policy unless you have disabled them. Sending units are identical to OEM and fit in the stock location. Run one side with the factory type oil sending and the other side to my manual oil pressure gauge.

It only controls the dash. The one in the water pump is for the PCM that controls the fans. Where is the oil sending unit located on the Trailblazer 4. Factory replacement Mustang temperature sending units are coolant temperature sending unit is located at the front of the Mustang lower intake and indicates the engine temperature to the temperature gauge. The sending unit is on the drivers side top rear of the engine.

Look for a coolant port and the sender unit scews into it. General Motors temperature gauge troubleshooting. As with any electrical troubleshooting it is best to check all wiring connections are clean, tight and free of corrosion. CHEVY SMALL BLOCK GEN I Gauge Sending Units. Location michigan city IN Posts 164.

Content submitted by Users is not endorsed by CarGurus, does not express the opinions of CarGurus, and should not be considered reviewe screene or approved by CarGurus.

Click on a number for a description of the component. Just finished with sending unit. Recrimped connection tighter with dielectric grease also added the extra ground wire from housing to frame. You have the sending unit as your TBI computer requires that signal to determine enrichment and advance. On my TBI the sender is almost exactly where it is shown in the aftermarket intake in the pic.

I had already purchased from you some time back. Whether you need a temperature switch for the 6CTA, or a Cummins ISC 8. It is screwed into the top rear portion of the left side cylinder head. My temperature gauge is not working so yesterday I replaced a temperature sending unit located out by the thermostat housing.

Of course this did not start the gauge working. So I searched the forum some more last night and found out there are two different coolant temperature sending units on the 4. Fits 351C and 351W engines. I am getting intermittent failure of the temperature to read and check engine light comes on. I have to relocate my water temperature sending unit to another location. Questions Is the water temperature the same on the left side vs the right side of the water passage ? CORVETTE COOLING TEMPERATURE SENSORS FOR ALL YEARS AND MODELS.

Home Seaboard Marine Store. This part controls the temperature signal going to the ECM not the gauuges. I thought it was the sending unit , which I BELIEVE is about centrally located on the manifold but when I replaced it, there was no change.

One id for the temperature gauge. This sending unit has always been slightly different than any. Camaro Cooling System And Camaro Coolant System Sending Units. Re: oil temperature sending unit location ?