700R4 speedometer gear

This is a retrofit gear to allow the speedometer to function with 3. Since the gear tooth pitch is slightly different than OE, the service life of this gear is limited to less than 20miles. Most cars and trucks with low rear end ratios will take a tooth drive gear. There are two driven gear housings, one for through tooth driven gears and one for through tooth driven gears.

For 700Rand BOP TH3type. A lot of people will change. The number on the driven gear housing must match the number of teeth on the driven gear. See all for 700rspeedometer gear.

RTransmissions have Speed-o-meter Gear Types: Compare the three photos to the gear set on your original transmission. VSS = Vehicle Speed Sensor VSS Drive Gear can be removed. RSPEEDOMETER GEAR INSTRUCTIONS In order to ensure accuracy of your speedometer please read the following information. Perfect for street or hot rod applications. Speedometer drive gear and clip 700rPATC.

Using the 10mm wrench remove the bolt securing the driven speedometer gear assembly (this is where the cable was attached). Shift Kits, Rebuild Kits And More! Remove the driven speedometer gear assembly.

Low Prices, Fast Free Shipping. Here is a photo of all the parts you are required to remove from the tranny in order to change the speedo gears. You see the tailshaft housing at top, the sleeve at bottom right, drive gear at bottom left, and the driven gear at left.

Also you see the rubber o-rings on the tailshaft housing and the sleeve. I keep breaking the driven gear on my 700Rspeedometer. I have an early (ish) 700Rthat has a spline input and as far as I know it came out of a 2WD truck.

Call today for the right gear for your application. All gears are subject to availability and may not be in stock. These gears are in stock and are ready to go. See the links below to get your speedometer gear , we have the 700rspeedometer gear , TH4speedometer gear , TH3speedometer gear , NP2speedometer gear , 7speedometer gear , and many more Drive and Driven speedometer gears as well.

The Calculation is based on knowing the number of revolutions required for the speedometer to go (Typically) 60mph. A speedo drive gear retainer clip for the TH3and 700RTurbo 3transmission in Chevrolet. This clip secures the speedo drive gear to the output shaft.

These ACDelco speedometer gear housing sleeves are designed to fit inside of the speedometer gear housing and hold the speedometer drive gear in place. They are manufactured from durable cast aluminum to exacting tolerances for a precise fit. Paul Cangialosi of 5Speeds. During the buil we needed to work out what speedometer gear I should.

Monster 700RConverter Sale, From Low-High Stall, Free Shipping.

Any gear housing from a mechanical speedo 700rshould fit. Or you could use a gear housing from a th3with a BOP case (Buick, Olds, Pontiac). Use the speedometer calculater from TCI or Bowtie overdrives website to calculate wish gears you need. After changing the rear gears from 3.

I have a light blue driven gear and am not anxious to remove the tail shaft. Enter your tire size Tire diameter may vary slightly depending on the manufacturer. Buy online, pick up in-store in minutes. R Billet Aluminum speedometer driven gear housing with new o-ring seal, lip.

L60’s reliability and performance issues. Welcome to Bowtie Overdrives, home of the worlds finest GM Automatic Overdrive Transmissions. Save 700rspeedometer gear to get e-mail alerts and updates on your eBay Feed. Unfollow 700rspeedometer gear to stop getting updates on your eBay Feed. We know our parts and products.

GM calls the part that mounts the speedometer driven gear to the transmission a Sleeve - Speedo Driven Gear. The speedometer I have is gear driven. How do I convert the tranny drive to the older gear drive for the speedo cable? Well, the 700ruse a TV cable as the speedometer , and the 4Lis an electronically controlled transmission , so if you see wires coming to the transmission on the rear of the transmission on the passenger side, you have a 4L60. The 700rdriven gear is the same as a th40 which means if you re-use the speedo drive gear your speedo will read faster.

In my case I lucked out, my 700rdrive gear (teeth) coupled with the randomnly selected th3driven gear (teeth) showed exactly twice actual road speed. Parts are just part of what we do. Get yours online today and pick up in store.

Gm 700rTransmission Front Pump Body Oil Seal 2wd Extension Housing Oil Seal. Also suggested is the purchase of a new speedometer O-ring to prevent any leaks on the new installation. Fill Your Cart With Color Today!

If you go to the bottom of the page you will see the gear options for the 700Rdrive gears and driven gears. When I did mine I took dive gear from the chart and it told me what driven gear I would need. I did this a couple times to get the correct gear count on the driven gear. A common problem for an LLV postal truck is a transmission fluid leak at the speedometer drive gear on the side of the transmission.

This video will show you how to repair this transmission leak at the seal. LLV stands for the Grumman Long Life Vehicle, which the United States Postal Service (USPS) for all mail delivery. To determine which speedometer gears are neede you need to know two things, tire diameter and rear end gear ratio.

This transmission was produced by General Motors, but is also sometimes known by the name Hydramatic. It is now considered to be one of the finest overdrive automatic transmissions ever produced. Truck, Manual, Custom kit AA. TH700Rthrough 4L70E tips and tricks.

Photo of typical 700R- 4Lseries servos. F-bodies) which had a hybrid speedometer gear and VSS. The drive gear is a worm gear located in the transmission , running off the output shaft.

It turns the driven gear , a pinion gear that is connected to the end of the speedometer cable.