Upper ball joint removal tool

The upper ball joint on A, B, and E-bodies require a special socket for removal. Replacing a ball joint is fast and easy and can be done with basic hand tools and a. I wanted to remove the upper ball joints as I was going to install the All-Pro inch uniball upper control arms. Before I tried to take the upper ball joint out of the new Tuff Country spindle, I decided to practice on a few of the factory ones to see just how hard it would be.

There are three different sizes, for A, B and C-bodies. Removes upper ball joint. In-Store Pickup: Choose In-store pick-up (OH, NV, GA, TX) on our web site.

And if you settle for a midrange ball joint tool kit, you stand to pay ten times less than you would for a repair conducted by a professional. How to Change a Ball Joint ! How To Use a Ball Joint Press ! Autozone Ball Joint Tool ! The goal is to try to guide it through the hole in the upper half of the. Features include a removable pin to fit into two pivot points for versatility. The weld must be cut before attempting to remove the ball joint. Assemble the ball joint press over the control arm as shown.

Select the correct size receiving tube, and position it under the vehicle ball joint. Tighten the forcing screw until the receiving tube contacts the control. Your order may be eligible for Ship to Home, and shipping is free on all online orders of $35. Designed to service most cars and light trucks, along with U-joints either on or off the vehicle.

If you are replacing the upper ball joint , undo the locknut on the underside and use your removal tool to pop it out. It is not necessary to remove the ball joint to replace the bushings. Now that the wishbones are free, you can remove the lock nuts that hold them, and the bushings, in place. Fill Your Cart With Color Today!

Check Out Tool Ball Joint on eBay. Put the ball joint separator between the control arm and the metal cap of the ball joint and hit the flat end of the separator with a hammer. Once the upper ball joint is separated from the control arm, remove it. Leave the nuts on a few threads to catch the knuckle when the ball joints break free of the axle. After removing the cotter pin (if equipped) use a 18mm wrench to loosen the ball joint nut about turns.

Do not remove the nut completely because it will protect the upper ball joint threads during removal. We know our parts and products.

Using the removal tool , tighten the castle nut with the large end facing outward. WD vehicles with half ton GM Style Dana axles. NOTE: Some cars and light trucks may have the upper ball joint spot-welded to the control arm. Push the upper control arm down to get new ball joint in place.

Install upper castle end nut. Verify the wheel alignment. Raise and support the vehicle. Ball joint removal tool (can be rented from local parts store). Upper Control Arm Replacement.

With this revolutionary design you can remove the ball joint from the front upper control arm without removing the arm from the vehicle, saving time and costs. Note that to remove the UBJ. Sunex Tools ball joint sockets works with you to remove and install ball joints easier. They are crafted from CR-MO alloy steel to provide a long service life and are available in sizes to fit a choice of applications. The ball joint separator allowed me to remove the joint from the upper and lower a-arms.

Our next move was to remove the snap rings from the ball joints as these actually help hold the joint in place. L upper ball joint removal problem. Teng Tools 16mm Heat Treated Drop Forged Ball Joint Separator -AT195. Next, use a ball joint removal tool to remove the ball joint.

The lower ball joint separated from the control arm. Clean the ball joint hole and line it. Step – Replace the ball joint. Next, Jack the truck up and place a stand under the frame rail. Here is the upper ball joint.

Find Tool Ball Joint Now!

The tool being discussed here is for the safe removal of the ball joint stud from the spindle. Buy online, pick up in-store in minutes. This is the tool - Amazon. All types of ball joint separators, ball joint pullers can be found in this section. It is the essential tool to use for ball joint replacement projects.

Expert Quality, designed for fast and simple removal or. I generally followed the biesan systems DIY, along with the Bentley manual. The procedure to replace the front upper ball joint is the same for both the left and right side. Using a ball joint removal tool separate the ball joint from the.

There is a special socket that fits the upper ball joint. Using that socket and an impact wrench it should come out pretty easy. It may be worth taking the control arms to a shop and having them done vs buying the socket though. Lower ball joint must be removed before any service can be performed on the upper ball joint. The retaining clip surrounds the top of the ball joints on some versions of the Beetle.

Normally, this is used on the lower ball joint assembly rather than the upper ball joint assembly. Using the pliers, spread the clip apart and pull it off the top of the joint.