Removing power steering pulley

Continue this action until the pulley becomes free of the pump input shaft. This is the SHORT version on how to remove and install a power steering pump pulley. A hydraulic power steering pump is driven by a serpentine or drive belt that is attached to the power steering pump pulley. Answered by a verified Chevy Mechanic We use cookies to give you the best possible experience on our website.

The power steering pump on a Ford vehicle works in conjunction with the power steering gear, to aid the driver in steering. On a Ford light truck or car, it is pressed onto the power steering pump shaft. It is held on by friction, meaning no bolts or retaining clips hold the pulley onto the shaft.

Find great deals on eBay for power steering pulley removal tool. Thanks for all the advise on the power steering pump pulley removal. It’s like Rod Knox type I need to get the pulley off to gain access to the mounting bolts. To do so, I have to get to those mounting bolts.

Replace the old power steering pulley with the new performance pulley. Grasp the new pulley with a rag and vice grips to hold the pulley in place while you tighten the securing nut on the pump shaft until tight. Do not attempt to disconnect the rag joint from the rack by removing the clamp joint.

Power steering system diagram:. Using a power steering pulley removal tool, remove the PS pulley. In the picture, a wood alignment tool is being used. The far end of the alignmnet tool rests on the crankshaft pulley , and the near end is on the power steering pulley.

Alignment is made with the power steering pulley puller and press. Hover over image to zoom. I was told i needed a Pulley removal tool but i really dont have any money until friday. Assemble the pulley removal tool on the front of the power steering pump pulley (Figure 2).

Thanks bjcsc I manufactured a pretty substantial puller from an old ball joint separator which uses the flange on the pulley boss to work against the shaft, but it just bent before budging the pulley. I also hate removing this pulley. The tool is called power steering. Re: power steering pulley removal. Thought it was the pump but discovered after removing the belt that the pulley is free wheeling on the pump shaft.

This presents an issue as I cannot figure out how to stop the pump shaft from spinning to loosen the bolt holding the pulley on. Install power steering pump to power steering pump support with three bolts. NOTE: The small diameter threads of the tool must be fully engaged in pump shaft before pressing on pulley.

I bought a rebuild kit for my power steering pump. The front seal appears to be where all of the mess is coming from. There are no pros to removing power steering from a car. The car is a good little car but by no means a race car and you just wind up looking dumb if you try to make it into one.

Removal of power steering pump. Alright guys here it is, the power steering removal DIY. I will be showing you routes: removal of PS only, and removal of PS and AC.

Most pics borrowed from Karcepts. Performance Tool pulley removal and installer tools are designed to remove power steering and alternator pulleys. They include a threaded bolt, a spacer nut, and an instruction manual.

Fill the power steering oil reservoir to the COLD FILL line. Pully is now off, I poured that sucker a tall glass of physics.

One part home-made breaker bar, one part harmonic balancer pulley puller, one part power steering pump pully puller (the nut that the wrench is hooked up to) And finally, One saucy wrench. Then attach a 10mm socket with ratchet to the end of the pulley removal tool, and attach a 10mm wrench to the nut of the pulley tool. Hold the ratchet in place as you rotate the wrench counterclockwise. Please note that the power steering pump pulley must be removed to access the pump retaining bolts. Special tools are required to draw the pulley off the pump shaft and to later press the pulley onto the pump shaft.

Step – Press off the power steering pump pulley.

Note the position of the pulley on the pump shaft. Grab your power steering pump removal tool, and position the fingers onto the edge of the pulley with the correctly sized rod (if needed) installed to remove the pulley. The pulley is flush with the end of the pulley shaft. Note: You can also leave the arm attached to the engine, and unbolt these two bolts directly from the power steering housing.

If you go this route you will have to unbolt the two bolts through the power steering pulley. Parts are just part of what we do. This tool is used to remove the pulley and also install it back onto the pump.

In that article we stated that you DO NOT use a gear puller, but specifically a pulley puller to remove the pulley. To take the pulley off with the power steering pump off the car. You will need: A large vise that can hold the power steering pump 19mm wrench 17mm wrench Lock the power steering pump in a vise with the pulley facing towards the ceiling. Although not a hard task, removing the pulley from the power steering pump on the TJ is something you will most likely have to do when you replace the power steering pump.

While attending the 5th Annual JeepsUnlimited Moab Run, my power steering pump started going out.

Than I removed the pulley and used a fine polishing paper inside the pulley hole smoothing the inner surface and removing a minute amount of metal. I then cleaned and oiled the pulley repeating this process until I was able to fully install the pulley. New power steering pulley installed.

Once the tension pulley and the power steering pulley have been loosene you should be able to slip the old belt off rather easily. Step 10: Place new belt on the pulleys. With the teeth side down, slide the new belt over the crankshaft pulley , the power steering pump pulley and the tensioner pulley.

As the pulley is driven by this belt and begins to spin, it turns an.