Dana 44 axle housing

With Dana’s innovative Crate Axle program, we’re making it even easier for you to get the exact OE-quality axle you nee right out of the box. Providing Expert Advice with over Years of Experience and Free Shipping on Orders Over $75. Find the entire axle assembly here at 4WD. The axle model number is cast in to the housing (3 , 60) either on the right (facing the axle cover) lower web at the point where the axle tube is pressed in to the center section or in the nose of the housing near the pinion yoke. There is no assembly neede just swap over your brakes and bolt it in.

The trail terminators are up to stronger than factory Bronco axles to keep you going on the trails. Only left in stock - order soon. Everything including the housing , gears, bearings, and axle shafts are brand new and manufactured to exacting standards. At a inch width and with massive 3. The fix for this is to straighten the axle in the jig, heat the housing with a torch, re-weld the plug welds, and weld the.

These new gussets can be added to your axle housing to prevent any damage to the knuckle balls, for. When you need a robust tandem drive axle , choose the DSH44. Jeep tj dana rear axle swap kit.

TeraT44= JK Wrangler upgrade housing (not re-using factory locker or shafts). Dana axle tube diameter is 3. Find low pinion housing , replacement kit, spindle to spindle drum and more. Available ratios for either option are 3. Jeep Parts, Jeep Soft Tops, Jeep Accessories, Jeep CJ Parts, Jeep Cherokee Parts.

All things Jeep from Morris 4xCenter your Jeep Parts Specialist. Unfortunately the guy who did this awesome. DTS Custom also rebuilds and modifies other rear-ends from cores. Housing and Axle Packages.

We have a Huge inventory of Used Axles, Spindles, Front and Rear partial and complete assemblies. For GM, Dodge, and some Mmilitary I. The couple of inches difference in pinion location make a big difference in the driveshaft angle. In general, start with an open knuckle housing with the differential on the correct side for your Jeep.

You might be able to put the bearing in the housing , and then beat the axle into it. Fill Your Cart With Color Today! Both tags contain similar information, however, the axle assembly tag contains the model number.

Shop our selection of Jeep axle housings. The tag faces forwar toward the engine. Designed to run the full length of the axle our truss helps distribute the load put on the front housing at any one time. The axle housing itself can be cut with a metal chop saw, band saw, porta-ban cut off wheel or even a hack saw if that is all you have and you need a good work out.

Slight correction to a previous post. This axle is used in a multitude of vehicles. With its strong reinforced center section, large diameter, thick wall tubes, and massive forged knuckles the RockJock housing is twice as strong as the stock factory unit. OD caps, which can be fitted to your existing driveshaft with the use of an adapter joint. You could always truss the axle to make it stronger, but at the end of the day, it’ll still have really weeks tubes.

This replacement housing can be used to build a heavy duty axle upgrade for both Rubicon and non-Rubicon JKs. Yes they use the same axles shafts but contrary to convention, the is not smaller than a , but rather bigger with a gear vs. Ive herd the dana ring and pinion is crap and that the dana is stronger. Ive also herd that the bearings and axle shafts in the dana are stronger and that the dana has a longer housing.

Lifetime warranty and come Pre-Assembled. Review(s) Your Price: $196. DANA Check US out every Week for New Products and Applications! The Danais a dry axle , thus meaning that the only gear oil that is in the axle housing is in the differential and not in the tube parts that the axle shafts go down which are completely dry of oil. Set Descending Direction.

Above, you can see the humps on the differential housing that needed to be removed.

Factory Rubicon inner axle shafts are not compatible with this housing (see page for more information). MADE THE AMERICAN WAY IN THE USA! The date of production is the first set of numbers stamped to the right of the differential. This was a metal peeling inside the axle housing , part of an old seal. Spyntec Industries LLC, the manufacturer of Solid Axle Industries products.

Solid Axle products hit the off-road community and earned the reputation as some of the highest quality driveline components in the industry. I was looking at what I thought was a ford axle but turns out it was a chevy. If you are starting a custom axle housing , call us for info on available lengths of shafts.

Chrome Moly Front Axle Shafts. Reassemble the axle housing by installing the axle shafts fully. From an economic viewpoint, buying a used car is a better choice.

Import means the blank forgings came from off shore, resulting in an economical choice if the ultimate in strength is not needed. Offering complete axle services in-house, we can straighten, truss, and custom build any housing you desire. Tapered axles have a nut on the wheel end of the axle shaft. Flanged axles will not work in a tapered axle housing.

A search would show that as well. Using appropriate size socket (approx. OD), force seal into housing until it is flush with end of axle tube. Wipe any excess gasket maker. JEEP WRANGLER JK FRONT DIFFERENTIAL DANA RUBICON 4RATIO AXLE.

Most popular chassis applications are available for immediate exchange. Fact - High pinion gears and housings are stronger than their low-pinion counterparts when installed in a front driving axle application. While that was being done I took a dremel to the old bearing race that was still in the axle housing using the.