Trans temp gauge install

We decided to install the larger plug because it gave the sensor much more contact area with the trans. Position gauge in mounting hole. Install mounting bracket, nuts and lock washers in position. Install one brass flat washer, one lock washer and one nut on each stud. If drilling a mounting hole in a panel to mount this gauge , the hole size should be 2. If you’ve got an automatic transmission in your Jeep, and you wheel a lot or tow a lot, it’s a good idea to install an auxillary transmission cooler.

It’s also nice to have a transmission temperature gauge so you can keep an eye on things. By having a trans temp gauge , you’ll be kept one step ahead of any possible issues involving overheating that could potentially seize your transmission. Pretty straightforward except where to put the sender. Stuper Duty Tranny (4R100) temp gauge install ? Test Port Extenders are available as well, which allow access to a vehicle’s test port in order to install temperature sensors. This is what I finally did to install a transmission temp gauge.

I wanted to install the sender in place of the drain plug. Repaired and Returned in Hours. The problem is the drain plug is M10x1.

If anyone could piont me in the right direction that would be great. There is a transmission temperature sensor in the transmission. It reports transmission temp to the PCM. IF you have a gauge that can read data off of the OBDII port you can read the output of this sensor. L Ford Powerstroke: You are on PAGE 1. The other part of the transmission fluid temperature control system that needs to be understoo set up and made to work correctly, is the torque converter lock up clutch.

This system is very easy to install , understand and use.

How to install an oil temperature gauge. Gauge Installation on a 7. The working temperature of your engine is normally kept to an optimum level by the cooling system. But there are occasions when your engine is worked harder and reaches temperatures higher than normal. You currently have posts.

I really would rather not use a test port in my trans case or hack up a hardline. Thinking of adding a transmission temp gauge I bought a relatively large boat that I will be pulling around next spring and I want to keep an eye on the tranny temp. It looks like I will have to cut a trans line anyway to do the install. Trans temp gauge install But they dont tell me what hole in the trans case I can install the sender.

If you look at my photos though I believe that there is a port on the side of the tranny for a gauge hook-up. I have also read that if you install a gauge in that port you will not receive a true temp reading. I do not want to drill the trans pan to install a gauge. I already have a braand new Auto Meter transmission temperature gauge. This is the normal place to install a temperature gauge or signal.

The temperature in this location will vary significantly with each vehicle start-up or hill. If the temperature reaches 300F (350F), reduce throttle. To lower the transmission temperature with the transmission in NEUTRAL, run the engine at 2RPM for 2-minutes to cool the oil. So, I did something about it and installed an aftermarket gauge. Re : trans temp gauge install ? To install , I just removed the stock plug, and drained out almost exactly quarts of tranny fluid (a lot more than the quarts the manual says for some reason).

The type of gauge is irrelevant, you can choose whichever you like the best. I just bought a transmission temperature gauge for my truck and upon reading the instructions, it says to install the sending unit in the return line back to the trans , after the cooler. I would think a person would want to monitor the actual temp of the trans before it goes to the cooler. Just decide where you want to mount the gauge and where you want to put your sending unit. I chose the transmission pan for my sending unit.

The gauge can be mounted anywhere you have room for it and provides line of sight. I have the speed 5-45RFE auto trans in my truck. Has anyone out there done a similar install ? I am wondering where the best place to put the sending unit bulb in the tranny. I screwed the temp gauge into the test port on the driver side of the trans. Not all transmissions are created equal, so not all transmission were built with a place to install a temperature sensor.

But a temperature sensors can be installed in several pre- existing places. Fellow members, Thanks for all your advise on installing gauges. I just installed my A-pillar pod mount and took your advise of an in-line install of Transmission temperature sensor instead of the welding of fitting to pan.

All right, i put in the sender unit and hooked it all up to the best of my know-how, but dosent work. After some research, I decided to pickup a digital temp gauge , along with a sender (the sender gets mounted in the transmission pan). I have a Hayden aftermarket trans cooler but need to monitor the temps.

As long as you have a large enough cooler you can have a yudge stall and still be fine.

With a correct sized cooler and converter locked up. Where do you guys have yours mounted and where did you put the sending unit for the gauge ? Here is a quick writeup on installing the stock tranny temp gauge into your cluster. I plan to install a trans temp gauge.

I will temporarily install the gas gauge needle in the trans - temp position.