Hood release cable replacement

In our first Back to Basics video Ed and I look at replacing the hood release cable - in this case on a Jeep Grand Cherokee. We know our parts and products. If you need a hood release cable replacement , you have come to the right place! At 1A Auto, we have just what you need to repair or replace broken or defective hood cables and bring back the safety and integrity of a safely latched hood.

This is a one unit cable with the handle attached. The average cost for a hood release cable replacement is between $1and $174. Labor costs are estimated between $1and $1while parts are priced at $46.

The cable runs from the front of the hood through the engine compartment, the firewall between the cabin and the engine bay, and finally to the back of the hood latch release located in the driver side foot below the steering wheel and above the brake and gas pedals. A damaged hood release cable is a snap to replace and is relatively inexpensive. Any car or truck will require replacement parts now and then, so when you need a Dorman hood release cable , PartsGeek. One cable runs from the hood release handle to the cable junction under the hood while the other ones run to each hood latch. As with the rest components, time can bring wear and tear to these cables.

The hood release cable on your Ford vehicle is the wire connector that allows you to open the hood when you pull on the hood release lever. In order to replace the this important cable , you will need to remove the hood latch and uninstall several bolts. The other cables (serviced as one part) run to each hood latch.

The cables that run to the hood latches tend to crack, allowing moisture to enter the cable. Grab the round ball on the end of the cable in the latch, and lift it up and out of the retainer spring. Your order may be eligible for Ship to Home, and shipping is free on all online orders of $35. Remove the screw holding the cable to the latch. Check here for special coupons and promotions.

The hood release actually consists of three cables: One that runs from the pull handle in the cabin to a two cable system that attaches to the hood releases. If your hood is starting to give you trouble releasing when you pull the cable you should take care of the problem right away. Step 5: Grab the new hood cable and connect one end to the release latch.

Next, run the cable along the other lines and hoses of the car up to the slit on the firewall. Secure the hood cable to the body with clips and on the other wires and hoses with zip ties. Inside the car, connect the other end to the release lever.

Trunk Latch Release Cable Replacement Service What is the Trunk Latch Release Cable all about? Had to use vise grip to pull open the latch. One of our premium quality replacement hoods will make your vehicle look like new at far less than the dealer price. The locking hood release cable is the cable that allows you to unlock your hood by pulling a lever inside your truck. It is a simple mechanism that uses no electronics.

The handle you pull is connected to a metal cable that is in turn connected to the latch that holds the hood closed. Made to the original factory specifications, this assembly includes T-handle, firewall grommet, and cable for a high quality restoration and a perfect OEM fit. If the cable is intact but the handle is broken off you can grab the end of the cable itself with a pair of vice grips or pliers and release it.

If your Mustangs hood release cable is broken or damaged replace it with a brand new replacement cable assembly from AmericanMuscle. Made of quality stainless steel, it naturally resists corrosion. The Jeep Cherokee hood release is operated by a cable that connects the release mechanism on the hood to the handle on the kick panel. As the cable ages, it can become hard to pull and can eventually fray. Our secure online payment system is much safer than using your credit card at your local retailer.

Disconnect the hood latch release handle cable (B) and remove the hood lower latch assembly (A). Corvette hood release cables can make the difference between easy engine compartment access and a stuck hood. Don’t get caught with your Corvette hood stuck because of a bad hood release cable.

If the cable broke by the hood release under the dash, you may be able to use a set of pliers to pull on the cable. To replace the hood release cable you must release the cable from the hood latch. Here is a diagram on what you are in for doing this job.

Please let us know what you find so it will help others.

At Car Parts Discount, we have real customer support agents available with enough expertise to help you purchase the correct Pontiac Bonneville part for your needs. I found some info here about getting the hood open. It was a bit tricky, but I got it out.

It looks like the ball at the hood end of the cable simply fell off. Q I saw you had a quick fix for getting under the hood of an older model bmw series while having a broken. Hood And Grille Products. Without your Chevrolet Chood release cable , looking under the hood will be a difficult task to say the least.

Many thanks to MVS Volvo Forum member tailor for working in sub-degree temperatures to document this fix and then for posting it up here! I Have The New Handle And The Old Cable Has A Good End To It Yet. How Do You Attach The Cable.

The cable that leads back to the interior release may be stretched or frayed. Using a screwdriver (A), lift the socket clips (B) up slightly on both ends of the lifter (D), and then remove the lifter from the bracket (C). Dorman Products is a leading supplier of original equipment dealer exclusive automotive and heavy duty replacement parts,.

Constructed of high-quality stainless steel, it naturally resists corrosion. Fill Your Cart With Color today! One day you pull on the trusty hood cable release handle and instead of easy access to your dipstick, there is just a nasty snap! These things bust in a couple of places. Our inventory selection includes replacement hoods, hood supports, hood latches, and release cables, as well as fender and hood seals, hood hinges, bumpers, and bushings to fulfill your Corvette needs.

Replace your broken or missing original with a quality replacement , features correct HOOD lettering and includes the mounting bracket. SOURCE: Broken hood release cable how to open hood. Thanks for the great write-up! Remove hood primary latch release cable handle.

Refer to Radiator Grille Reinforcement Support Replacement. Contributed by: Mark Taylor Recently I pulled on the front hood release lever and felt the sickening snap of the last strands of the cable breaking.

To open the hood on your Honda you can try the following procedures. Push down on the hood where the hood latch is located and hold the hood down.